-07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
-07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Terve,
Eukon 2007 GC:n apukuskin puoleinen etuvalon lyhyt polttimo ei pala. Mittarilla mittasin johdon päästä ja tulee vain 6 volttia?!
minnekkä on voinna kadota puolet volteista? Johdot näyttää ehjiltä.
Valo alkoi temppuilemaan niin että paloi toisinaan ja toisinaan taas ei... Nyt koko ajan pimeänä..
Onko näissä joku valojen ohjain jossain?
Eukon 2007 GC:n apukuskin puoleinen etuvalon lyhyt polttimo ei pala. Mittarilla mittasin johdon päästä ja tulee vain 6 volttia?!
minnekkä on voinna kadota puolet volteista? Johdot näyttää ehjiltä.
Valo alkoi temppuilemaan niin että paloi toisinaan ja toisinaan taas ei... Nyt koko ajan pimeänä..
Onko näissä joku valojen ohjain jossain?
ex 2006 KJ 2,8CRD Aut.
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Body Control Module ohjaa, mutta pitäis siellä olla rele jossain, soitas mulle aamulla 11.00 jälkeen, niin katsotaas...
Vai olikohan se jo tuossa toi Front Control Module, ei suoraan kyllä muista...
Vai olikohan se jo tuossa toi Front Control Module, ei suoraan kyllä muista...
Your Jeep specialist
Jeep Comanche -89, 4,0L6+AW-4+NP-231+Dana30+Dana35 w/POWERTRAX w/ 4"+ korotus & HD-steering sekä Jeep Wagoneer Limited -79, 360V8+TH-400+Quadra-Trac projekti
FJDC #1
Jeep Comanche -89, 4,0L6+AW-4+NP-231+Dana30+Dana35 w/POWERTRAX w/ 4"+ korotus & HD-steering sekä Jeep Wagoneer Limited -79, 360V8+TH-400+Quadra-Trac projekti
FJDC #1
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Pittää koittaa keritä soittaa!
Tuolla ainakin jotain sähkölöistä:
http://www.wkjeeps.com/wk_fuses.htm
HEADLAMPS
The headlamp system includes the SCM, the EMIC, the FCM, and the left (lighting) multi-function switch on the steering column. The headlamp bulbs have a path to ground at all times through their connection to the headlamp and dash wire harness. The headlamp and dash wire harness has takeouts with eyelet terminals that are secured by ground screws to the front end sheet metal within the engine compartment.
The SCM monitors a hard wired multiplex input to determine the status of the left multi-function switch and whether the headlamp high or low beams are selected. The SCM then sends the appropriate electronic headlamp switch and headlamp beam select switch status messages to the FCM over the CAN data bus. The FCM responds to these messages by providing a pulse width modulated voltage output to the proper headlamp bulbs through the right and left low and high beam feed circuits to illuminate the selected headlamp beams. The FCM also sends the appropriate electronic messages to the EMIC to control the illumination of the high beam indicator.
The FCM also remembers which beams (LOW or HIGH) were selected when the headlamps were last turned OFF, and energizes those beams again the next time the headlamps are turned ON. The FCM provides a battery saver (load shedding) feature for the headlamps, which will turn these lamps OFF if they are left ON for more than about eight minutes with the ignition switch in the LOCK position. The SCM provides a fail-safe feature for the headlamps, which will send an electronic message to the FCM to turn the low beam headlamps ON automatically if the SCM detects no input from the left multi-function switch. The FCM also provides a fail-safe feature for the headlamps that will turn the headlamps ON automatically whenever a loss of CAN bus communication is detected with the ignition switch in the ON position.
Each headlamp includes an integral reflector adjustment screw to be used for static aiming of the headlamps.
Tuolla ainakin jotain sähkölöistä:
http://www.wkjeeps.com/wk_fuses.htm
HEADLAMPS
The headlamp system includes the SCM, the EMIC, the FCM, and the left (lighting) multi-function switch on the steering column. The headlamp bulbs have a path to ground at all times through their connection to the headlamp and dash wire harness. The headlamp and dash wire harness has takeouts with eyelet terminals that are secured by ground screws to the front end sheet metal within the engine compartment.
The SCM monitors a hard wired multiplex input to determine the status of the left multi-function switch and whether the headlamp high or low beams are selected. The SCM then sends the appropriate electronic headlamp switch and headlamp beam select switch status messages to the FCM over the CAN data bus. The FCM responds to these messages by providing a pulse width modulated voltage output to the proper headlamp bulbs through the right and left low and high beam feed circuits to illuminate the selected headlamp beams. The FCM also sends the appropriate electronic messages to the EMIC to control the illumination of the high beam indicator.
The FCM also remembers which beams (LOW or HIGH) were selected when the headlamps were last turned OFF, and energizes those beams again the next time the headlamps are turned ON. The FCM provides a battery saver (load shedding) feature for the headlamps, which will turn these lamps OFF if they are left ON for more than about eight minutes with the ignition switch in the LOCK position. The SCM provides a fail-safe feature for the headlamps, which will send an electronic message to the FCM to turn the low beam headlamps ON automatically if the SCM detects no input from the left multi-function switch. The FCM also provides a fail-safe feature for the headlamps that will turn the headlamps ON automatically whenever a loss of CAN bus communication is detected with the ignition switch in the ON position.
Each headlamp includes an integral reflector adjustment screw to be used for static aiming of the headlamps.
ex 2006 KJ 2,8CRD Aut.
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Oletko kokeillut toisella polttimolla? Taitaa olla aika hankala mitata(vissiinkin)tuota jännitettä koska se vaihtelee 0-12voltin välillä eli on eräänlaista vaihtovirtaa/pulssivirtaa. Joku enemmän elektroniikasta perillä oleva voisi tietää enemmän? Elikkä voipi olla hyvällä lykyllä tullut polttimolla tunnit täyteen..
wh 3.0 crd -07
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Otin koko johtosarjan irti valaisimen takaa ja mittasin sen pöydällä. Eli johdot siltä osin ok.
Sen jälkeen laitoin paikoilleen ja mittasin 6 volttia.
Polttimon olen vasta vaihtanut ja se ei pelittänyt silloin, mutta syttyi taas satunnaisesti...
Pitää kokeilla toisella polttimolla...
Sen jälkeen laitoin paikoilleen ja mittasin 6 volttia.
Polttimon olen vasta vaihtanut ja se ei pelittänyt silloin, mutta syttyi taas satunnaisesti...
Pitää kokeilla toisella polttimolla...
ex 2006 KJ 2,8CRD Aut.
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Ei toimi toisellakaan polttimolla...
ex 2006 KJ 2,8CRD Aut.
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Ei oo relettä, FCM hoitaa, eli oliskohan se viallinen?? Se pitäis saada nyt sitten testeriin, että näkis, mitä siellä modulissa tapahtuu...
Your Jeep specialist
Jeep Comanche -89, 4,0L6+AW-4+NP-231+Dana30+Dana35 w/POWERTRAX w/ 4"+ korotus & HD-steering sekä Jeep Wagoneer Limited -79, 360V8+TH-400+Quadra-Trac projekti
FJDC #1
Jeep Comanche -89, 4,0L6+AW-4+NP-231+Dana30+Dana35 w/POWERTRAX w/ 4"+ korotus & HD-steering sekä Jeep Wagoneer Limited -79, 360V8+TH-400+Quadra-Trac projekti
FJDC #1
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Merkillä arveli että on mennyt vikatilaan.
Pitäisi nollautua lukijalla.
Huomenna käyn nollaamassa.
Pitäisi nollautua lukijalla.
Huomenna käyn nollaamassa.
ex 2006 KJ 2,8CRD Aut.
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Sekin on yksi teoria, jännä kuulla auttaako....
Your Jeep specialist
Jeep Comanche -89, 4,0L6+AW-4+NP-231+Dana30+Dana35 w/POWERTRAX w/ 4"+ korotus & HD-steering sekä Jeep Wagoneer Limited -79, 360V8+TH-400+Quadra-Trac projekti
FJDC #1
Jeep Comanche -89, 4,0L6+AW-4+NP-231+Dana30+Dana35 w/POWERTRAX w/ 4"+ korotus & HD-steering sekä Jeep Wagoneer Limited -79, 360V8+TH-400+Quadra-Trac projekti
FJDC #1
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Patriot teki samaa.. Lopulta oli vikakoodi modulissa että valossa oikosulku. Vikakoodi pois ja taas toimii. Oli polttimon palaessa menny ilmeisesti oikosulkuun ja tullu viivakoodi. Tuo tuleva jännite on ilmeisesti joku diagnostiikan mittajännite. Bosch kts540 yleistesteri toimi täydellisesti tässä korjauksessa. Valo toiminu ongelmitta useamman vuoden nyt.
kozel@ircnet
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Ja kyseessä oli vasen ajovalo ja lähivalo.
kozel@ircnet
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
eivät saaneet merkilläkään testerillä nollatuksi vikakoodia.
Ilmeisesti johdotuksessa vikaa...
Ilmeisesti johdotuksessa vikaa...
ex 2006 KJ 2,8CRD Aut.
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
Re: -07 Grand Cherokeen lyhyt etuajovalo ei toimi apukuskin puolella?
Yksi pinni oli löystynyt jostain liitoksesta
ex 2006 KJ 2,8CRD Aut.
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME
*MYYDÄÄN! 2001 TJ Wrangler 4,0 Aut.
*1987 YJ Wrangler 4,2 Aut. +6" Skyjacker +2"BL
*1980 & 1984 SJ Cherokee 4,2 Man.
*2007 WK Grand Cherokee 3.0 CRD Aut. QD2 +2" OME